# Support & Troubleshooting **URL:** https://opensourceleg.discourse.group/c/help/12.md?page=1 [Latest](https://opensourceleg.discourse.group/latest.md) · [Categories](https://opensourceleg.discourse.group/categories.md) **Page:** 2 --- ## [Loadcell disconnecting](https://opensourceleg.discourse.group/t/loadcell-disconnecting/147)
**Author:** [@cangelid](https://opensourceleg.discourse.group/u/cangelid)\ **Replies:** 0\ **Last updated:** [October 29, 2025, 11:04pm UTC](https://opensourceleg.discourse.group/t/loadcell-disconnecting/147 "2025-10-29T23:04:36Z")
Hi all, I’m experiencing an issue with my OSL setup where the loadcell starts the zeroing process, completes the calibration, and begins streaming data normally, but then becomes unresponsive after some time. I am eithe… --- ## [Is the RPi5 supported or should we stay with the RPi4b?](https://opensourceleg.discourse.group/t/is-the-rpi5-supported-or-should-we-stay-with-the-rpi4b/141)
**Author:** [@EdgarBolivar](https://opensourceleg.discourse.group/u/EdgarBolivar)\ **Replies:** 1\ **Last updated:** [October 22, 2025, 6:51pm UTC](https://opensourceleg.discourse.group/t/is-the-rpi5-supported-or-should-we-stay-with-the-rpi4b/141 "2025-10-22T18:51:59Z")
Hello, everyone. Is the RPi5 supported or should we stay with the RPi4b? The dimensions between those two are compatible, but we would appreciate any recommendations regarding software dependencies. P.S. This is my fir… --- ## [OpenSourceLeg.org Cannot View Videos](https://opensourceleg.discourse.group/t/opensourceleg-org-cannot-view-videos/136)
**Author:** [@Troy](https://opensourceleg.discourse.group/u/Troy)\ **Replies:** 2\ **Last updated:** [October 6, 2025, 12:09pm UTC](https://opensourceleg.discourse.group/t/opensourceleg-org-cannot-view-videos/136 "2025-10-06T12:09:40Z")
Hello, I was looking at the updated website and saw that there were new instructional videos on how to assemble the OSL. However, the embedded videos seem to have some sort of access issue. I am still able to follow the… --- ## [FSM Walking Controller Example - ValueError: State Machine isn't active](https://opensourceleg.discourse.group/t/fsm-walking-controller-example-valueerror-state-machine-isnt-active/44)
**Author:** [@cangelid](https://opensourceleg.discourse.group/u/cangelid)\ **Replies:** 2\ **Last updated:** [September 26, 2025, 9:51pm UTC](https://opensourceleg.discourse.group/t/fsm-walking-controller-example-valueerror-state-machine-isnt-active/44 "2025-09-26T21:51:43Z")
Greetings to the community! I’m trying to use the FSM walking controller example supplied in the latest version of OpenSourceLeg on GitHub. When I run it, I get the ValueError: State machine isn’t active. From what… --- ## [Available documentation on the Dephy DAQ board](https://opensourceleg.discourse.group/t/available-documentation-on-the-dephy-daq-board/126)
**Author:** [@Axel](https://opensourceleg.discourse.group/u/Axel)\ **Replies:** 1\ **Last updated:** [September 26, 2025, 4:08pm UTC](https://opensourceleg.discourse.group/t/available-documentation-on-the-dephy-daq-board/126 "2025-09-26T16:08:19Z")
Hi all, I’ve been searching for documentation on the Dephy Load Cell Amplifier Board, but haven’t had any luck so far. Do you happen to have access to the schematics or a datasheet? Either one would be pretty helpful. M… --- ## [RPi Compute Module board: USB-C and display outputs](https://opensourceleg.discourse.group/t/rpi-compute-module-board-usb-c-and-display-outputs/34)
**Author:** [@malizade](https://opensourceleg.discourse.group/u/malizade)\ **Replies:** 1\ **Last updated:** [September 14, 2025, 1:57pm UTC](https://opensourceleg.discourse.group/t/rpi-compute-module-board-usb-c-and-display-outputs/34 "2025-09-14T13:57:54Z")
Hi. On the adapter board for the RPi Compute Module, there are three USB-C ports. 1- Can any of them be used to power the board? (because there is also a batter connector) 2- Is there a display output? If so, which on… --- ## [Wi-Fi on the interface board](https://opensourceleg.discourse.group/t/wi-fi-on-the-interface-board/36)
**Author:** [@Axel](https://opensourceleg.discourse.group/u/Axel)\ **Replies:** 1\ **Last updated:** [September 4, 2025, 8:46pm UTC](https://opensourceleg.discourse.group/t/wi-fi-on-the-interface-board/36 "2025-09-04T20:46:55Z")
Hi, Does the interface board (see image) for connecting to the Raspberry Pi CM5 include a Wi-Fi module? I couldn’t find the documentation for this board on the OSL2 website, which would be very helpful to have. --- ## [Building OS: Free to access network](https://opensourceleg.discourse.group/t/building-os-free-to-access-network/35)
**Author:** [@Axel](https://opensourceleg.discourse.group/u/Axel)\ **Replies:** 1\ **Last updated:** [September 3, 2025, 2:34am UTC](https://opensourceleg.discourse.group/t/building-os-free-to-access-network/35 "2025-09-03T02:34:53Z")
Hi, When creating the secrets (following the guide described here), if the network I want to add does not require a username or password, should I include the secrets “ENTNETWORK\_IDENTITY“ and “ENTNETWORK\_PASSWORD“ ? C… --- ## [Specify acceptable heat treatments for 17-4PH steel parts](https://opensourceleg.discourse.group/t/specify-acceptable-heat-treatments-for-17-4ph-steel-parts/33)
**Author:** [@Troy](https://opensourceleg.discourse.group/u/Troy)\ **Replies:** 2\ **Last updated:** [August 28, 2025, 6:03pm UTC](https://opensourceleg.discourse.group/t/specify-acceptable-heat-treatments-for-17-4ph-steel-parts/33 "2025-08-28T18:03:33Z")
Please specify acceptable heat treatments for the 17-4PH steel parts. [Previous page](https://opensourceleg.discourse.group/c/help/12.md)